At SANlight, personal consultation is a priority.

Hang the luminaire in your desired location. Make sure it is securely fastened.

• 1: First, connect the power supply cable to the luminaire.
• 2: Insert the power plug into the socket.

For optimal illumination of your cultivation area, we recommend the following setups:

EVO 3-60 for a cultivation area of 60x60cm

• number of luminaires: 1
• Height (H): 40cm
• position of lights: central
• Tilt (T): 0°

EVO 3-80 for a cultivation area of 80x80cm

• number of luminaires: 1
• Height (H): 40cm
• position of lights: central
• Tilt (T): 0°

EVO 3-100 for a cultivation area of 100x100cm

• number of luminaires: 2
• Height (H): 30cm
• position of lights: 60cm between the lights, 20cm from the walls
• Tilt (T): 11°

EVO 4-120 for a cultivation area of 120x120cm

• number of luminaires: 2
• Height (H): 30cm
• position of lights: 70cm between the lights, 25cm from the walls
• Tilt (T): 11°

EVO 5-150 for a cultivation area of 150x150cm

• number of luminaires: 2
• Height (H): 50cm
• position of lights: 90cmbetween the lights, 30cm from the walls
• Tilt (T): 0°

There are plenty of different connection options available for the SANlight EVO System, which led us to the conscious decision not to include a power cord to every luminaire. Not only does it protect
our planet from senseless pollution, it also saves valuable resources. It allows you the possibility and flexibility to build a system tailored to your needs, and is easier on your wallet.

If space is limited, we recommend using angled supply cables and extension cables. Below you will find all the necessary components to operate 2 luminaires of the EVO Series with one power plug.
Further connection options can be found on our webpage.

All connections made with SANlight products are IP65 certified. This means that your SANlight System is protected against dust and water jets and is suitable for safe use even in high humidity. Warning: To preserve IP65 protection all open connectors have to be closed with the EVO Protective Cap (including open connectors of the H Connector). The rating doesn`t include wall plugs or other non-SANlight electrical connections! Warning: This doesn’t include wall plugs or other electrical connections!

All luminaires within the EVO Series are “ready to dimm”. There are two different dimmers available: SANlight M-Dimmer and SANlight BT-Dimmer. Be aware that every
luminaire must be equipped with its own dimmer.

SANlight M-Dimmer: We recommend this magnetic dimmer especially for smaller installations of up to approximately 10 lights. After the dimmer is connected to your
luminaire, you can dim it in 4 steps from 100% to 40%. You can also activate a soft start (simulated sunrise) using the magnetic key supplied.

SANlight BT-Dimmer: The Bluetooth dimmer is recommended for all installations. You can integrate from 1 up to a maximum of 32 000 luminaires into a Bluetooth mesh.
Individual lighting groups can easily be set up, dimmed, and controlled.

The dimmer as well as the matching slot are marked in blue. The dimmer may only be used in this slot.

• Remove the end cap of the blue connector
• Plug the dimmer into the blue connector
• Now follow the individual operating instructions for BT- or M-Dimmers

The EVO Series luminaires have a favourable design, allowing you to hang the luminaire at an inclined angle. This will improve the homogeneity of the illuminated area, especially in small areas.

With the Easy-Tilting system you can choose between 3 different angles: 0°, 11°, 17°.

Your EVO luminaire is IP65 certified. This means that the entire luminaire is dustproof and protected against water jets. Be aware that this protection is only guaranteed if the end cap or a SANlight dimmer is mounted on the blue connector and the EVO power cable is connected to the black connector.

To clean the optics of your EVO luminaire, please use a soft, non-abrasive cloth with distilled water. No cleaning agents needed.